Posts

COMMERCIAL

This project was built to deliver treated water for an irrigation system in a farm

DESIGN PARAMETERS
WATER SOURCE
Brackish water Well, Chlorine free
TEMPERATURE
20 °C to 30 °C
FEED TDS
<5500 ppm
INTEL FLOW
14.3 M3H
PERMATE FLOW
10.41 M3H
RECOVERY RATE
73%

The RO unit Includes the appropriate high-pressure pump, FRP pressure vessels, spiral wound thin film composite RO membranes, Sch 80 PVC low pressure feed piping, and high-pressure piping or hose. 

This RO system is skid mounted assembled, hydro-tested and functionally tested before leaving our factory.

The RO system supplied includes PLC based controls and is capable of automatic operation with minimal operator intervention. Safety devices are provided to protect the RO system and its components from common fault conditions.

Level controls, located in the owner’s permeate storage tank, will send a control
signal to the RO system control panel to begin the start sequence.


At the start signal the feed valve will open and membrane flush valves will open. At the end of the pre-flush cycle the membrane flush valve will close.


As water pressure builds in the RO high pressure feed pump suction line, a pressure switch senses the line pressure of the water entering the pump. This switch activates a timer which delays further start sequences until all water lines and pressure vessels reach normal start-up pressures. At the end of the time delay, a start control signal is sent to the RO high pressure feed pump starter.

The RO high pressure feed pump then starts and supplies the necessary feed water
pressure to the membrane array.


The RO feed water is split into two streams, permeate or purified water and concentrate or reject water. The RO permeate flows to the permeate water storage tank. The concentrate is disposed of in accordance with local environmental regulations or method of reuse. When the permeate storage tank is full the level switch sends the shutdown signal to the RO control panel and the system then begins it’s post-flush cycle which removes all concentrated contaminants from the system. Once complete, the system waits for the next start signal.

Check out more Brackish Water systems pre-engineered designs.

PHYSICAL DATA & DIMENSIONS :

WhatsApp
Email
Facebook
Twitter
LinkedIn

COMMERCIAL

This project was built to deliver treated water for an irrigation system in a farm

DESIGN PARAMETERS
WATER SOURCE
Brackish water Well, Chlorine free
TEMPERATURE
20 °C to 30 °C
FEED TDS
<5500 ppm
INTEL FLOW
14.3 M3H
PERMATE FLOW
10.41 M3H
RECOVERY RATE
73%

The RO unit Includes the appropriate high-pressure pump, FRP pressure vessels, spiral wound thin film composite RO membranes, Sch 80 PVC low pressure feed piping, and high-pressure piping or hose. 

This RO system is skid mounted assembled, hydro-tested and functionally tested before leaving our factory.

The RO system supplied includes PLC based controls and is capable of automatic operation with minimal operator intervention. Safety devices are provided to protect the RO system and its components from common fault conditions.

Level controls, located in the owner’s permeate storage tank, will send a control
signal to the RO system control panel to begin the start sequence.


At the start signal the feed valve will open and membrane flush valves will open. At the end of the pre-flush cycle the membrane flush valve will close.


As water pressure builds in the RO high pressure feed pump suction line, a pressure switch senses the line pressure of the water entering the pump. This switch activates a timer which delays further start sequences until all water lines and pressure vessels reach normal start-up pressures. At the end of the time delay, a start control signal is sent to the RO high pressure feed pump starter.

The RO high pressure feed pump then starts and supplies the necessary feed water
pressure to the membrane array.


The RO feed water is split into two streams, permeate or purified water and concentrate or reject water. The RO permeate flows to the permeate water storage tank. The concentrate is disposed of in accordance with local environmental regulations or method of reuse. When the permeate storage tank is full the level switch sends the shutdown signal to the RO control panel and the system then begins it’s post-flush cycle which removes all concentrated contaminants from the system. Once complete, the system waits for the next start signal.

Check out more Brackish Water systems pre-engineered designs.

PHYSICAL DATA & DIMENSIONS :

WhatsApp
Email
Facebook
Twitter
LinkedIn


PROJECT DESCRIPTION
BRACKISH WATER REVERSE OSMOSIS SYSTEM - 65,000 GPD

Industrial - irrigation

This project was built to deliver treated water to irrigate a golf course

DESIGN PARAMETERS
WATER SOURCE
Well, chlorine free
TEMPERATURE
28 °C
FEED TDS
<12,000 ppm
PRODUCT TDS
< 500 ppm
FEED FLOW
100.0 GPM
PRODUCT FLOW
45.0 GPM
OPERATING PRESSURE
300-350 PSI
RECOVERY RATE
40-45%

Single pass, single stage. Four (4) pressure vessel total, that contains twenty (20) LG NanoH2O membranes. The system it’s set to produce 65,000 US Gal/day of product water at 45% recovery.

This system was designed to  be shipped and transported in an anodized aluminum skid.

main features

PHYSICAL DATA & DIMENSIONS :

WhatsApp
Email
Facebook
Twitter
LinkedIn


PROJECT DESCRIPTION
SEA WATER REVERSE OSMOSIS SYSTEM - 12,000 GPD

COMMERCIAL - HOTEL

In a remote island in Central America, the system provides water to a small - state of the art - hotel

DESIGN PARAMETERS
WATER SOURCE
Well, chlorine free
TEMPERATURE
25 °C
FEED TDS
25,500 – 36,000 ppm
PRODUCT TDS
< 390 ppm
FEED FLOW
21.9 GPM
PRODUCT FLOW
8.3 GPM
OPERATING PRESSURE
727 PSI
RECOVERY RATE
38%

Single pass, single stage. One pressure vessel total, that contains 3 thin-film composite elements in series. The system produces 45.4 m3/day (12,000 GPD or 8.3 GPM) of product water at 38% recovery.

main features

ANCILLARY EQUIPMENT

PHYSICAL DATA & DIMENSIONS :

WhatsApp
Email
Facebook
Twitter
LinkedIn

COMMERCIAL - IRRIGATION

This project was built to deliver treated water for an irrigation system in a farm

Single pass, single stage. Three (3) pressure vessel total, that contains twelve (12) LG NanoH2O membranes. The system it’s set to produce 65,000 US Gal/day of product water at 45% recovery.

The pre-treatment system consisted six (6) media filters for removing suspended solids.

This system was designed to  be shipped and transported in a aluminum skid.

main features

ANCILLARY EQUIPMENT

PHYSICAL DATA & DIMENSIONS :

WhatsApp
Email
Facebook
Twitter
LinkedIn


PROJECT DESCRIPTION
SEAWATER REVERSE OSMOSIS SYSTEM - 50,000 GPD

COMMERCIAL - IRRIGATION

This project was built to deliver treated water for the irrigation system of one of the biggest and famous golf curses in Latin America

DESIGN PARAMETERS
WATER SOURCE
Seawater well, chlorine free
TEMPERATURE
25 °C
FEED TDS
25,500 – 36,000 ppm
PRODUCT TDS
395-450 ppm
FEED FLOW
64.0 GPM
PRODUCT FLOW
24.3 GPM
OPERATING PRESSURE
750 – 850 PSI
RECOVERY RATE
38%

Single pass, single stage. Two pressure vessel total, that contains eight (8) LG NanoH2O membranes. The system it’s set to produce 50,000 US Gal/day of product water at 38% recovery.

We worked with a PX  as our go to Energy Recovery Device in this one. All of our system was mounted in an aluminum skid ready to ship in a 40′ container.

main features

PHYSICAL DATA & DIMENSIONS :

WhatsApp
Email
Facebook
Twitter
LinkedIn


PROJECT DESCRIPTION
SEAWATER REVERSE OSMOSIS SYSTEM - 3,000 GPD

INDUSTRIAL - DRINKING WATER

The four (4) systems supply water to living quarters exploration facility. Two of them on small towns supporting local population and others in the oil platform for drinking proporses of the exploration team

DESIGN PARAMETERS
WATER SOURCE
Brackish well, chlorine free
TEMPERATURE
20-28 °C
FEED TDS
<1,000 ppm
PRODUCT TDS
< 300 ppm
FEED FLOW
51.0 GPM
PRODUCT FLOW
34.7 GPM
OPERATING PRESSURE
100-115 PSI
RECOVERY RATE
68%

Four (4) skid mounted seawater reverse osmosis systems set to produce 3,000 GPD of product water.

This system had one a pre-treatment system that consisted of one (1) multimedia filter, one (1) antiscalant injection pump and one (1) ultraviolet lamp for desinfection.

The RO system had three (3) pressure vessels with a single membrane array.

We also integrated a post-treatment system that had one (1) re-mineralization tank and a chlorine injection pump.

main features

ANCILLARY EQUIPMENT

PHYSICAL DATA & DIMENSIONS :

WhatsApp
Email
Facebook
Twitter
LinkedIn


PROJECT DESCRIPTION
SOLAR BRACKISH WATER REVERSE OSMOSIS SYSTEM - 50,000 GPD

INDUSTRIAL - ICE CREAM FACTORY

Supplying 70% of the icecream of an island in the caribbean. System provides water to icecream production.

DESIGN PARAMETERS
WATER SOURCE
Brackish well, chlorine free
TEMPERATURE
20-28 °C
FEED TDS
<1,000 ppm
PRODUCT TDS
< 300 ppm
FEED FLOW
51.0 GPM
PRODUCT FLOW
34.7 GPM
OPERATING PRESSURE
100-115 PSI
RECOVERY RATE
68%

Advanced Equipment and Services has successfully completed commissioning and start-up of a state of the art 30,000 US GPD reverse osmosis system. This system has been design to work at 85% recovery rate with a very low working pressure. The final user is large a multinational company factory located in a small island were water and power are limited.

This system works 100% automatically with a permeate flushing system that will extend membrane operational life expand. Customer maintenance manager Luis Pena comment’s ” This system has been running with a very low operational cost and minimum maintenance we are very happy we got the right equipment from the right company”

Since the water is so scarce, the 15% reject flow coming out of the reverse osmosis system is used for flushing toilets in the factory general quarters, making this system a truly zero discharge equipment.

main features

ANCILLARY EQUIPMENT

WhatsApp
Email
Facebook
Twitter
LinkedIn