COMMERCIAL
This project was built to deliver treated water for an irrigation system in a farm
The RO unit Includes the appropriate high-pressure pump, FRP pressure vessels, spiral wound thin film composite RO membranes, Sch 80 PVC low pressure feed piping, and high-pressure piping or hose.
This RO system is skid mounted assembled, hydro-tested and functionally tested before leaving our factory.
The RO system supplied includes PLC based controls and is capable of automatic operation with minimal operator intervention. Safety devices are provided to protect the RO system and its components from common fault conditions.
Level controls, located in the owner’s permeate storage tank, will send a control
signal to the RO system control panel to begin the start sequence.
At the start signal the feed valve will open and membrane flush valves will open. At the end of the pre-flush cycle the membrane flush valve will close.
As water pressure builds in the RO high pressure feed pump suction line, a pressure switch senses the line pressure of the water entering the pump. This switch activates a timer which delays further start sequences until all water lines and pressure vessels reach normal start-up pressures. At the end of the time delay, a start control signal is sent to the RO high pressure feed pump starter.
The RO high pressure feed pump then starts and supplies the necessary feed water
pressure to the membrane array.
The RO feed water is split into two streams, permeate or purified water and concentrate or reject water. The RO permeate flows to the permeate water storage tank. The concentrate is disposed of in accordance with local environmental regulations or method of reuse. When the permeate storage tank is full the level switch sends the shutdown signal to the RO control panel and the system then begins it’s post-flush cycle which removes all concentrated contaminants from the system. Once complete, the system waits for the next start signal.
Check out more Brackish Water systems pre-engineered designs.
PHYSICAL DATA & DIMENSIONS :
- Dimensions: 200X36X75 inc.
- Weight: 2,590 lb.
related information
PROJECT DESCRIPTION STATIONARY DIALYSIS RO WATER TREATMENT SYSTEMS
Our Stationary RO Dialysis Water treatment Unit provides the required high standards water quality for any Dialysis center, clinic or hospital.
The sizing of our equipment can be adapted based on the patient population of the center, clinic or hospital.
SPECIFICATIONS
- 3 membranes 4×40
- 2 HP stainless steel RO pump
- Weight: 395 lbs. (179kg)
- Size: 36x19x71 inch. (91x48x180 cm)
- 3/4” feed connection
- 1/2” product connection
- 1/2” reject connection
standard
optional equipment
- Stainless Steel Multistage
- PLC driven control panel
- 15″ HMI for operator interface
- Stainless-Steel Pressure Vessels
- Powder Coated Aluminum Frames
- Mema 4X electrical equipment
- 5 Micron Sediment Pre-filter
- Product TDS Monitor
- Permeate/Concentrate Flowmeters
- High and Low Pressure Protection
- Automatic Inlet Valve
- Pre and Post Flush
- Pretreatment Lockout
- Factory Performance Tested
- Sample Valves
- Pressure Gauges
- Cleaning Connections
- Remote control
- UV sterilization
- Chlorination
- Dichlorination
- PH adjust
- MM filters (sand, anthracite, activate carbon)
- Ion exchanger
- Corrosion inhibitor
- Turbidity monitor
related information
PROJECT DESCRIPTION
DOUBLE PASS HIGH PURITY BRACKISH WATER RO SYSTEM 25,000 GPD
The Reverse Osmosis (RO) System provides a Robust construction and is designed with conservative standards for versatility in the event of feed water quality and temperature variations. The system design has incorporated a 15% allowable fouling or flux decline for the membranes without loss of system product water capacity. A pre and post cycle raw water membrane flush has been incorporated into the system design to minimize membrane fouling and piping corrosion during shutdown periods.
The Reverse Osmosis (RO) system includes the appropriate high pressure pump, FRP pressure vessels, spiral wound thin film composite RO membranes, Sch 80 PVC low pressure feed piping, and high pressure piping or hose. The RO unit provides as skid mounted, pre-assembled, pre-wired and is fully operationally tested at the factory prior to shipment.
All Advancees’s Reverse Osmosis (RO) systems includes PLC based controls and are capable of automatic operation with minimal operator intervention. Safety devices are provided to protect the RO system and its components from common fault conditions.
The RO feed water is split into two streams, permeate or purified water and concentrate or reject water. The RO permeate flows to the permeate water storage tank. The concentrate is disposed of in accordance with local environmental regulations or method of reuse. When the permeate storage tank is full the level switch sends the shutdown signal to the RO control panel and the system then begins it’s post-flush cycle which removes all concentrated contaminants from the system. Once complete, the system waits for the next start signal.
main features
- Monitoring screen helps to assure water product meets the require standard before and during dialysis operation
- Automatic rinse cycles, helping to preserve water quality under control
- Easy interphase with operator facilitates system operation
- Feed and permeate Water Conductivity are display for customer peace of mind making sure water meets quality standard
- Pressure switch protects system in case of unexpected shutoff feed water supply
related information
PROJECT DESCRIPTION
SEAWATER CONTAINERIZED REVERSE OSMOSIS SYSTEM - 50,000 GPD
DRINKING WATER - MUNICIPALITY
This project was built to deliver treated water for all amenities (showers, kitchen, pools, restaurants and waterpark) in a 500 rooms hotel in a remote island.
Single pass, single stage. Two pressure vessel total, that contains twelve (12) thin film membranes. The system it’s set to produce 50,000 US Gal/day of product water at 45% recovery.
The pre-treatment system consisted of four (4) media filters for removing suspended solids, iron and chlorine.
This containerized seawater desalination system was designed to fit and operate in a 20 ft ISO Container ready to ship and install.
main features
- Inlet actuator valve
- 5 Micron cartridge filter
- 5 HP multistage centrifugal High Pressure Pump
- Motor variable frequency driver (VFD)
- Low- and high-pressure protection
- Two (2) FRP high rated pressure vessel with four (4) membrane array
- Clean in place and flush system integrated
- NEMA 12 enclosure
- PLC controller
- 15” HMI for operator interface
- Product and reject flowmeter
- Conductivity monitor
- Sample valves
ANCILLARY EQUIPMENT
- 4 multimedia filters 48” diam. x 62” high (pre-treatment)
PHYSICAL DATA & DIMENSIONS :
- 20' ISO Container
- Weight: 1,050 lb.
related information
PROJECT DESCRIPTION
MOBILE RO DIALYSIS WATER TREATMENT SYSTEMS - 576 GPD
Easy to transport Mobile RO Dialysis Water treatment Unit provides the required flexibility for integration into hospital and home needs. The system it’s set to produce 0.4 US Gal/minute of product water at 20% recovery.
Water pre-treatment included. It consists of sediment and activated carbon filters to remove suspended solids and residual chlorine from incoming feed water.
main features
- Monitoring screen helps to assure water product meets the require standard before and during dialysis operation
- Emergency protection, in case of high salinity feed water or low-pressure system will react accordingly and provide message to operator
- Provides a permeate capacity of 90 l/h
- Automatic rinse cycles, helping to preserve water quality under control
- Easy interphase with operator facilitates system operation
- Water pretreatment included
- Feed and permeate Water Conductivity are display for customer peace of mind making sure water meets quality standard
- Pressure switch protects system in case of unexpected shutoff feed water supply
PHYSICAL DATA & DIMENSIONS :
- Dimensions: 36" x 24" x 12"
- Weight: 65 lb.
related information
PROJECT DESCRIPTION SEA WATER REVERSE OSMOSIS SYSTEM - 100,000 GPD
DRINKING WATER - MUNICIPALITY
This project was built to deliver treated water for needed communities (approx. 3,200 people) where the municipal water service is deficient.
For this project we delivered two (4) containerized sea water reverse osmosis systems, complete with pre-treatment, flush and post- treatment modules.
Each SWRO had a single pass, single stage, four (4) pressure vessel total, that contained twenty four (24) thin-film composite elements.
The system produces 100,000 GPD or 69.5.0 GPM of product water at 45% recovery.
main features
- Inlet actuator valve
- 5 Micron cartridge filter
- 75 HP multistage centrifugal High Pressure Pump
- Energy Recover Device (ERD) - Turbo charger
- Motor variable frequency driver (VFD)
- Low- and high-pressure protection
- FRP high rated pressure vessel with a three (3) membrane array
- Clean in place and flush system integrated
- NEMA 12 enclosure
- PLC controller
- 15” HMI for operator interface
- Product and reject flowmeter
- Conductivity monitor
- Sample valves
ANCILLARY EQUIPMENT
- 7.5HP centrifugal feed pump
- 4 multimedia filters 48” diam. x 62” high (pre-treatment)
- Antiscalant injection system (pre-treatment)
PHYSICAL DATA & DIMENSIONS :
- Dimensions: 10' x 4' x 6'
- Weight: 1,050 lb.
related information
PROJECT DESCRIPTION
SEAWATER REVERSE OSMOSIS SYSTEM - 400,000 GPD
DRINKING WATER - MUNICIPALITY
This project was built to deliver treated water for needed communities (approx. 12,000) where the municipal water service is deficient.
For this project we delivered four (4) containerized seawater reverse osmosis systems, complete with pre-treatment, flush and post- treatment modules. Each system was installed and shipped in two (2) 40ft container.
Each SWRO had a single pass, single stage, fourteen (14) pressure vessel total, that contained ninety eight (98) thin-film composite elements.
The system produces 400,000 GPD or 277.0.0 GPM of product water at 45% recovery.
main features
- Inlet actuator valve
- 5 Micron cartridge filter
- 300 HP multistage centrifugal High Pressure Pump
- Energy Recovery Device (ERD) - Turbo charger
- Motor variable frequency driver (VFD)
- Low- and high-pressure protection
- FRP high rated pressure vessel with a seven (7) membrane array
- Clean in place and flush system integrated, 25HP SS multistage centrifugal pump and a 800gal polyethilene tank
- NEMA 12 enclosure
- PLC controller
- 15” HMI for operator interface
- Product and reject flowmeter
- Conductivity monitor
- Sample valves
ANCILLARY EQUIPMENT
- 25HP centrifugal feed pump
- Six (6) multimedia filters 68” diam. x 72” high (pre-treatment)
- Antiscalant injection system (pre-treatment)
PHYSICAL DATA & DIMENSIONS :
- Dimensions: 40' container
- Weight: 16,000 lbs (aprox)
related information
PROJECT DESCRIPTION BRACKISH WATER REVERSE OSMOSIS SYSTEM - 65,000 GPD
Industrial - irrigation
This project was built to deliver treated water to irrigate a golf course
Single pass, single stage. Four (4) pressure vessel total, that contains twenty (20) LG NanoH2O membranes. The system it’s set to produce 65,000 US Gal/day of product water at 45% recovery.
This system was designed to be shipped and transported in an anodized aluminum skid.
main features
- Inlet actuator valve
- 5 Micron cartridge filter
- 30 HP multistage centrifual High Pressure Pump
- Motor variable frequency driver (VFD)
- Low- and high-pressure protection
- FRP high rated pressure vessel with a five (5) membrane array
- Clean in place and flush system integrated
- NEMA 12 enclosure
- PLC controller
- 15” HMI for operator interface
- Product and reject flowmeter
- Conductivity monitor
- Sample valves
PHYSICAL DATA & DIMENSIONS :
- Dimensions: 15' x 6' x 6'
- Weight: 4,200 lb.
related information
PROJECT DESCRIPTION
SEAWATER REVERSE OSMOSIS SYSTEM 100,000 GPD
DRINKING WATER
This project was built to deliver treated water for needed communities (approx. 4,000 people) where the municipal water service is deficient.
For this project we delivered four (4) containerized sea water reverse osmosis systems, complete with pre-treatment, flush and post- treatment modules.
Each SWRO had a single pass, single stage, four (4) pressure vessel total, that contained twenty four (24) thin-film composite elements.
The system produces 100,000 GPD or 69.5.0 GPM of product water at 45% recovery.
main features
- Inlet actuator valve
- 5 Micron cartridge filter
- 75 HP multistage centrifugal High Pressure Pump
- Energy Recover Device (ERD) - Turbo charger
- Motor variable frequency driver (VFD)
- Low- and high-pressure protection
- FRP high rated pressure vessel with a three (3) membrane array
- Clean in place and flush system integrated
- NEMA 12 enclosure
- PLC controller
- 15” HMI for operator interface
- Product and reject flowmeter
- Conductivity monitor
- Sample valves
ANCILLARY EQUIPMENT
- 7.5HP centrifugal feed pump
- 4 multimedia filters 48” diam. x 62” high (pre-treatment)
- Antiscalant injection system (pre-treatment)
PHYSICAL DATA & DIMENSIONS :
- Dimensions: 10' x 4' x 6'
- Weight: 1,050 lb.
related information
Industrial Park Coral Springs
Coral Springs, Florida (New Location):
12070 NW 40 St, Coral Springs, FL 33065